| | | i310s 電流鉗表的工作原理基于霍爾效應技術，適合測量直流和交流電流。 i310s 可以與示波器和其它適當的記錄儀表配合使用，從而進行**的非侵入式電流測量。 | - Current Ranges: 30 A and 300 A ACRMS or ±45 A and 450 A DC
- Measuring Ranges: ±45 A and 450 A dc
- Output Sensitivity: 10 mV/A (40 A) to 1 mV/A (400 A)
- Resolution: ±50 mA (40 A) to ±100 mA (400 A)
- Load Impedance: > 10 k Ohms and ￡ 100 pF
- Frequency Range (small signal): DC to 20 kHz (- 3 dB)
- Phase Shift below 1 kHz, < 2 degrees
- Temperature Coefficient: ±0.1% of reading / °C
- Power Supply: 9 V Alkaline
| Electrical Characteristics | | Current Ranges | | | 30 A and 300 A ACRMS or ±45 A and 450 A DC | | | ACRMS or DC | | | Inrush Current | | | Output Sensitivity | | | 10 mV/A (30 A) | | | 1 mV/A (300 A) | | | Accuracy (at +23°C) | | (30A range) | ±1% of reading ±50 mA | | (300A range) | ±1% of reading ±300 mA | | | Bandwidth to meet accuracy specification | | | Phase Shift below 1 kHz | | | Resolution | | | ±50 mA (30 A) | | | ±100 mA (300 A) | | | Load Impedance | | | Conductor Position Sensitivity | | | ±1.5% relative to centre reading | | | Frequency Range | | (small signal) | DC to 20 kHz (- 3 dB) | | | Temperature Coefficient | | | Power Supply | | | Battery Life | | | 30 Hours, low battery indicator | | | Working Voltage (see Safety Standards section) | | | General Characteristics | | Maximum Conductor Size | | | Output Connection | | | Safety BNC connector | | | Supplied with safety 4mm adaptor | | | Output Zero | | | Manual adjust via thumbwheel | | | Cable Length | | | Operating Temperature Range | | | Storage Temperature Range (with battery removed) | | | Operating Humidity | | | 15% to 85% (non-condensing) | | | Weight | | | Safety Standards | | BS EN 61010-1 | | | BS EN 61010-2-032 | | | BS EN 61010-031 | | | 300 VRMS, Category III, Pollution Degree 2 | | | Note | | | Use of the probe on un-insulated conductors is limited to 300 V ACRMS or DC and frequencies below 1 kHz. | | | EMC Standards | | BS EN 61236 | 1998 +A1, A2, & A3 | |
> | 80i-110s 交/直流電流鉗 | | | | | | AC/DC Current clamp The 80I-110s is compatible with any Fluke ScopeMeter Test Tool, Power Harmonics Analyzer, Oscilloscope, Multimeter, or other voltage measurement device that has the following features: BNC input connectors or if using a meter convert the banana plugs to a BNC connector using the adapter PM9081/001. - Current Range: 0.1 to 100A DC or 0.1 to 70A AC
- Basic Accuracy (DC to 1kHz):
100mV/A setting: 50mA to 10A +/- 3% of reading + 50mA
10mV/A setting: 50mA to 40A +/- 4% of reading + 50mA
40A to 80A +/- 12% of reading + 50mA
80 to 100A +/- 15% of reading - Output Signal: 10A range: 100mV/A | 100A range: 10mV/A
- Bandwidth: 1Hz to 20kHz
- Working Voltage: 600V AC rms
- Maximum Conductor Size: 11.8 mm (.46 inch) diameter
- Safety Rating: IEC 1010 and CSA-C22.2 No. 1010-1 Installation Category II, Working Voltage 600V
|
|
| 型號名稱 | 描述 | | 80i-110s | 交/直流電流鉗 (100 A) | | | | | |
> | |
